Metal Legend kit – Dragon


(All rights belong to their owners. Images used here for review purposes only.)

Back in July, I mentioned that I’d picked up the Gakken Metal Legend dragon kit, but that I wasn’t going to build it right away. Well, in August I built it. Again, these kits consist of flat parts made from soft metal, probably tin. You can bend most of the pieces with your fingers, but sometimes you need the slot tool provided in the box. Most of the kits are for either dinosaurs or insects, and are in the 1,000-1,400 yen range ($10-$14 USD). Dragon was 2,400 yen. (I went back to the bookstore I bought this from, and most of their other kits are gone now. No indication that Gakken will come out with a second Metal Lord, but I hope they do.)

The booklet that comes with the kit has 6 pages of pictures and descriptions of dragons through history, from Europe, Japan and China.

The rest of the booklet has the assembly instructions, plus one page of suggestions for customizing the kit.


(Neck support structure and main torso, assembled.)

I didn’t count the number of pieces, but I’d guess it would come out pretty close to 50, not including the nuts and bolts. Most of the pieces were already fully punched out, but a few were connected together and needed to be separated. The metal is so soft that I could easily cut them with a small scissors, without damaging the scissors. I also didn’t keep track of exactly how long I spent on this kit. I’m pretty sure I worked on it for 2 hours one night, and then 2 more hours the following day. I did have some problems following the instructions (I didn’t try translating it from the Japanese) and ended up putting the head on upside down twice. When I got near to the end of the assembly, I apparently made a mistake in mounting the tail connection hinge (or, I was mistaken in thinking it was a mistake, and could have just swung the hinge piece out) and I then disassembled the entire body and removed the head to get to the hinge piece within the torso assembly. Regardless, I did take the body apart once, and disassembled the head 3 times.


(Torso with finished neck plates, plus the pieces for the head. The eyes and teeth are actually plastic decals. There are a couple different decal designs to choose from.)

The bolt mounting the head to the neck was just short enough as to make threading on the nut a real pain. That was the only place where I had to resort to using tweezers to hold the nut, and using pliers to squeeze the head assembly to be more narrow. The bolt has to thread through the outer head shell, the jaw, the tongue and the neck piece, which isn’t all that easy. Screwing up and having to do that a total of 4 times was not fun.


(All the sub-assemblies are finished, and the tail hinge at the back of the torso is extended correctly now.)

For the most part, making the sub-assemblies wasn’t difficult, just fiddly. But, it is important to fold the metal the correct way the first time. Folding, then refolding does stress the thinner metal bands, and risks causing them to snap. In fact, one of the leg pieces didn’t quite double over exactly right, with one side being a little higher than the other so that the bolt holes didn’t line up. When I tried correcting the fold, the little metal band between the two parts of the leg snapped on me. Fortunately, that piece was covered up by other sheet metal, and the break didn’t adversely affect anything. At the time, I was worried that I’d messed up the kit.

The hinge points attaching the wings, legs and tail to the main torso all consist of a metal pin that force-fits into a plastic grommet, so they are intended to pivot if so desired. The neck spine and tail are single strips of metal; you can bend them if you want, but they’re not actually hinged.

The box advertises that the dragon is 37 cm (14.5″) long. It’s a bit shorter than that if you curve the tail. Still, it’s the biggest kit in the Gakken metal series, and, it’s gotten me a lot of attention when I brought it to restaurants. It makes a great centerpiece in the middle of a table. Definitely worth buying and building if you like making stuff.

Because the box says that the Dragon is part of the “Metal Legend series,” I’m hoping a second large kit is going to come out at some point.

Advertisements
Leave a comment

3 Comments

  1. theluneon

     /  October 2, 2016

    Looks awesome! :O Well done
    I hope you succeed in obtaining and assembling the other kits as well

    Reply
    • Thank you. I have built a couple of the smaller metal insect kits, which were fun. Haven’t seen anything new come out for the bigger metal lords, though.

      Reply
      • Actually, looking at the Gakken metal kit webpage, it looks like The Dragon was a one-shot, which came out in 2014. I was making the insect kits in 2015-16, and I know the Dragon was not on the store shelves at that time. I assume that the store either pulled it out of inventory, or someone else special ordered it, then cancelled the order. Either way, given Gakken’s track record of creating a new “series” that never has more than one kit in it, I’m not hopeful that they’ll do anything more with this series in the future.
        https://kids.gakken.co.jp/kagaku/mag_kagaku/metalkit/

        Reply

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: